Skip to main content
DD-CAT IDE logoDD-CAT IDE

TL431 + optocoupler Forwardfeedback calculation

Favoriteused 1 times

Typical secondary-side TL431+optocoupler feedback for forward: divider, LED limiting resistor, primary-side current derivation and margin checks (tap after the output LC filter; see notes for compensation).

Key points

TL431 + optocoupler Forwardfeedback calculation: Typical secondary-side TL431+optocoupler feedback for forward: divider, LED limiting resistor, primary-side current derivation and margin checks (tap after the output LC filter; see notes for compensation). Formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. The forward converter is a Buck-derived topology with no right-half-plane zero; its output LC resonance is low, so Type II compensation is common (zero near 1/10 crossover, pole near half the switching frequency) — this tool only computes DC operating-point resistors. The divider tap must be after the output LC filter; for remote sensing, account for sense-line drop and filtering to avoid injecting switching ripple into the loop.

Inputs

Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min

Calculation model (updates with parameters)

Secondary side (output sensing)Primary side (opto transistor pulls FB down)Vled 5 VR_led464 ΩVoutRu9.76 kΩRl9.76 kΩsecondary GNDTL431R_pu10 kΩVpu 5 VPWM ICFB ← Ic 470 µAprimary GNDVout = 4.99 V(target 5.0 V) | If = 3.017 mA | CTR 30%
[Divider] R1 (top) / R2 (bottom)9.76 kΩ / 9.76 kΩ
[Divider] alternative 19.53 kΩ / 9.53 kΩ
[Divider] alternative 29.31 kΩ / 9.31 kΩ
[Divider] alternative 39.09 kΩ / 9.09 kΩ
[Divider] sense current255.6 µA
[LED limiting] R_led464 Ω
[LED limiting] actual If3.017 mA
[LED limiting] R_led dissipation4.224 mW
[Primary] FB required current Ic470 µA
[Primary] derived If_min1.567 mA
[Primary] current margin1.9 ×
[TL431] cathode current3.017 mA

Engineering notes

  • The forward converter is a Buck-derived topology with no right-half-plane zero; its output LC resonance is low, so Type II compensation is common (zero near 1/10 crossover, pole near half the switching frequency) — this tool only computes DC operating-point resistors.
  • The divider tap must be after the output LC filter; for remote sensing, account for sense-line drop and filtering to avoid injecting switching ripple into the loop.
  • Optocoupler CTR degrades noticeably with temperature and aging; re-check If needs using the datasheet minimum ×0.7. Insufficient margin shows up as output drift at high temperature and full load.

FAQ

What is TL431 + optocoupler Forwardfeedback calculation for?
Typical secondary-side TL431+optocoupler feedback for forward: divider, LED limiting resistor, primary-side current derivation and margin checks (tap after the output LC filter; see notes for compensation).
What is the formula for TL431 + optocoupler Forwardfeedback calculation?
Core formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using TL431 + optocoupler Forwardfeedback calculation?
The forward converter is a Buck-derived topology with no right-half-plane zero; its output LC resonance is low, so Type II compensation is common (zero near 1/10 crossover, pole near half the switching frequency) — this tool only computes DC operating-point resistors. The divider tap must be after the output LC filter; for remote sensing, account for sense-line drop and filtering to avoid injecting switching ripple into the loop. Optocoupler CTR degrades noticeably with temp…
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.