Skip to main content
DD-CAT IDE logoDD-CAT IDE

TL431 + optocoupler Flybackfeedback calculation

Favoriteused 6 times

Typical secondary-side TL431+optocoupler feedback for flyback: enumerate the divider from standard series, compute the LED limiting resistor, and derive the required primary current with CTR margin checks.

Key points

TL431 + optocoupler Flybackfeedback calculation: Typical secondary-side TL431+optocoupler feedback for flyback: enumerate the divider from standard series, compute the LED limiting resistor, and derive the required primary current with CTR margin checks. Formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. CCM flyback has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ. The compensation network (Type II, RC between REF and cathode) is tuned to the target crossover — this tool only computes DC operating-point resistors. In standby / no-load, if the required LED current drops below 1mA, add a resistor R≈(Vout−2.5V)/1mA from Vout to the TL431 cathode to keep it in its linear region.

Inputs

Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min

Calculation model (updates with parameters)

Secondary side (output sensing)Primary side (opto transistor pulls FB down)Vled 12 VR_led2.8 kΩVoutRu5.23 kΩRl1.37 kΩsecondary GNDTL431R_pu10 kΩVpu 5 VPWM ICFB ← Ic 470 µAprimary GNDVout = 12.02 V(target 12.0 V) | If = 3 mA | CTR 30%
[Divider] R1 (top) / R2 (bottom)5.23 kΩ / 1.37 kΩ
[Divider] alternative 111.8 kΩ / 3.09 kΩ
[Divider] alternative 216.5 kΩ / 4.32 kΩ
[Divider] alternative 310.2 kΩ / 2.67 kΩ
[Divider] sense current1.821 mA
[LED limiting] R_led2.8 kΩ
[LED limiting] actual If3 mA
[LED limiting] R_led dissipation25.2 mW
[Primary] FB required current Ic470 µA
[Primary] derived If_min1.567 mA
[Primary] current margin1.9 ×
[TL431] cathode current3 mA

Engineering notes

  • CCM flyback has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ. The compensation network (Type II, RC between REF and cathode) is tuned to the target crossover — this tool only computes DC operating-point resistors.
  • In standby / no-load, if the required LED current drops below 1mA, add a resistor R≈(Vout−2.5V)/1mA from Vout to the TL431 cathode to keep it in its linear region.
  • Too-small R_led raises LED current and standby loss; too-large lowers loop gain and worsens load regulation — pick a middle value with If=2–5mA.

FAQ

What is TL431 + optocoupler Flybackfeedback calculation for?
Typical secondary-side TL431+optocoupler feedback for flyback: enumerate the divider from standard series, compute the LED limiting resistor, and derive the required primary current with CTR margin checks.
What is the formula for TL431 + optocoupler Flybackfeedback calculation?
Core formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using TL431 + optocoupler Flybackfeedback calculation?
CCM flyback has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ. The compensation network (Type II, RC between REF and cathode) is tuned to the target crossover — this tool only computes DC operating-point resistors. In standby / no-load, if the required LED current drops below 1mA, add a resistor R≈(Vout−2.5V)/1mA from Vout to the TL431 cathode to keep it in its linear region. Too-small R_led raises LED current and standby loss; too-large lower…
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.