RCD / RDC Clamp Snubber Design
RCD clamp for flyback leakage spikes: clamp resistor / capacitor / ultrafast diode values, loss, and drain stress.
Key points
RCD / RDC Clamp Snubber Design: RCD clamp for flyback leakage spikes: clamp resistor / capacitor / ultrafast diode values, loss, and drain stress. Formula: R = 2Vc(Vc−Vro)/(Llk·Ipk²·fsw) | C = Vc/(R·ΔV·fsw) | P = ½Llk·Ipk²·fsw·Vc/(Vc−Vro). Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. Raising Vclamp lowers loss (P ∝ Vc/(Vc−Vro)) but also raises drain stress — back-solve the limit from a 15–20% Vds margin. The clamp diode must be ultrafast (trr ≤ 35ns) with VRRM ≥ 1.2× drain peak; a slow diode re-injects energy during recovery, causing secondary ringing.
Inputs
R = 2Vc(Vc−Vro)/(Llk·Ipk²·fsw) | C = Vc/(R·ΔV·fsw) | P = ½Llk·Ipk²·fsw·Vc/(Vc−Vro)Calculation model (updates with parameters)
Bode plot (magnitude / phase, updates with parameters)
| Clamp resistor R | 21.88 kΩ | R = 2Vc(Vc−Vro)/(Llk·Ipk²·fsw) |
| Clamp resistor dissipation | 1.828 W | Absorbs all leakage energy; allow ≥2× margin (two paralleled 2512 is common) |
| Clamp capacitor C | 9.375 nF | Derive from ripple ratio; use film / low-ESR with voltage ≥ 1.5×Vclamp |
| actual ripple ΔV | 15 V | 7.5% × Vclamp |
| Drain peak voltage | 575 V | Vin(max) + Vclamp |
| Vds margin ratio | 11.5 % | Needs >15–20%; too low means a higher-voltage MOS is required |
| node ringing frequency (estimate) | 4.109 MHz | 1/(2π√(Llk·Coss)); the clamp branch must look low-impedance here |
| Clamp diode | VRRM ≥ 690 V | average current ≈ 9.141 mA; ultrafast recovery trr ≤ 35ns |
Engineering notes
- Raising Vclamp lowers loss (P ∝ Vc/(Vc−Vro)) but also raises drain stress — back-solve the limit from a 15–20% Vds margin.
- The clamp diode must be ultrafast (trr ≤ 35ns) with VRRM ≥ 1.2× drain peak; a slow diode re-injects energy during recovery, causing secondary ringing.
- The RCD only clamps the spike, not the ringing: hand residual ringing to an RC snubber (another tool in this group) or a secondary rectifier RC.
FAQ
- What is RCD / RDC Clamp Snubber Design for?
- RCD clamp for flyback leakage spikes: clamp resistor / capacitor / ultrafast diode values, loss, and drain stress.
- What is the formula for RCD / RDC Clamp Snubber Design?
- Core formula: R = 2Vc(Vc−Vro)/(Llk·Ipk²·fsw) | C = Vc/(R·ΔV·fsw) | P = ½Llk·Ipk²·fsw·Vc/(Vc−Vro). The tool returns results instantly using this formula and the selected parameters.
- What engineering notes should I keep in mind when using RCD / RDC Clamp Snubber Design?
- Raising Vclamp lowers loss (P ∝ Vc/(Vc−Vro)) but also raises drain stress — back-solve the limit from a 15–20% Vds margin. The clamp diode must be ultrafast (trr ≤ 35ns) with VRRM ≥ 1.2× drain peak; a slow diode re-injects energy during recovery, causing secondary ringing. The RCD only clamps the spike, not the ringing: hand residual ringing to an RC snubber (another tool in this group) or a secondary rectifier RC.
Embed this calculator on your site / blog / intranet
Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.