TL431 + optocoupler Forwardfeedback calculation
Typical secondary-side TL431+optocoupler feedback for forward: divider, LED limiting resistor, primary-side current derivation and margin checks (tap after the output LC filter; see notes for compensation).
Key points
TL431 + optocoupler Forwardfeedback calculation: Typical secondary-side TL431+optocoupler feedback for forward: divider, LED limiting resistor, primary-side current derivation and margin checks (tap after the output LC filter; see notes for compensation). Formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. The forward converter is a Buck-derived topology with no right-half-plane zero; its output LC resonance is low, so Type II compensation is common (zero near 1/10 crossover, pole near half the switching frequency) — this tool only computes DC operating-point resistors. The divider tap must be after the output LC filter; for remote sensing, account for sense-line drop and filtering to avoid injecting switching ripple into the loop.
Inputs
Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_minCalculation model (updates with parameters)
| [Divider] R1 (top) / R2 (bottom) | 9.76 kΩ / 9.76 kΩ | actual output 4.99 V | error 0.20% |
| [Divider] alternative 1 | 9.53 kΩ / 9.53 kΩ | Vout 4.99 V | error 0.20% |
| [Divider] alternative 2 | 9.31 kΩ / 9.31 kΩ | Vout 4.99 V | error 0.20% |
| [Divider] alternative 3 | 9.09 kΩ / 9.09 kΩ | Vout 4.99 V | error 0.20% |
| [Divider] sense current | 255.6 µA | ≥0.25mA (≥60× the ≤4µA REF bias) |
| [LED limiting] R_led | 464 Ω | (Vled−Vf−Vka)/If, Vka = 2.5V; ideal 466.7 Ω |
| [LED limiting] actual If | 3.017 mA | |
| [LED limiting] R_led dissipation | 4.224 mW | |
| [Primary] FB required current Ic | 470 µA | (Vpu−0.3V)/R_pu, with Vce_sat ≈ 0.3V |
| [Primary] derived If_min | 1.567 mA | Ic / CTR_min = Ic / 30% |
| [Primary] current margin | 1.9 × | If / If_min; recommend ≥1.5× |
| [TL431] cathode current | 3.017 mA | meets the 1mA minimum cathode current |
Engineering notes
- The forward converter is a Buck-derived topology with no right-half-plane zero; its output LC resonance is low, so Type II compensation is common (zero near 1/10 crossover, pole near half the switching frequency) — this tool only computes DC operating-point resistors.
- The divider tap must be after the output LC filter; for remote sensing, account for sense-line drop and filtering to avoid injecting switching ripple into the loop.
- Optocoupler CTR degrades noticeably with temperature and aging; re-check If needs using the datasheet minimum ×0.7. Insufficient margin shows up as output drift at high temperature and full load.
FAQ
- What is TL431 + optocoupler Forwardfeedback calculation for?
- Typical secondary-side TL431+optocoupler feedback for forward: divider, LED limiting resistor, primary-side current derivation and margin checks (tap after the output LC filter; see notes for compensation).
- What is the formula for TL431 + optocoupler Forwardfeedback calculation?
- Core formula: Vout = Vref × (1 + Ru/Rl) | R_led = (Vled − Vf − Vka)/If | If_min = Ic / CTR_min. The tool returns results instantly using this formula and the selected parameters.
- What engineering notes should I keep in mind when using TL431 + optocoupler Forwardfeedback calculation?
- The forward converter is a Buck-derived topology with no right-half-plane zero; its output LC resonance is low, so Type II compensation is common (zero near 1/10 crossover, pole near half the switching frequency) — this tool only computes DC operating-point resistors. The divider tap must be after the output LC filter; for remote sensing, account for sense-line drop and filtering to avoid injecting switching ripple into the loop. Optocoupler CTR degrades noticeably with temp…
Embed this calculator on your site / blog / intranet
Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.