RC Snubber Design
Ring damping for MOS / relay switching nodes: dual-frequency extraction of strays, with R/C values, loss, and an impedance Bode plot.
Key points
RC Snubber Design: Ring damping for MOS / relay switching nodes: dual-frequency extraction of strays, with R/C values, loss, and an impedance Bode plot. Formula: f_ring = 1/(2π√(LC)) | R = √(L/C) | Cs = 2~3Cp | P = Cs·ΔV²·fsw. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. Two-frequency method: ① measure ringing f₁ at the switching node; ② parallel a known small Cadd and measure f₂; ③ solve Lp / Cp — more reliable than guessing strays. Also applies to relay / thyristor contacts (often start with 100Ω + 100nF); for contacts, put R in series before C to limit inrush.
Inputs
f_ring = 1/(2π√(LC)) | R = √(L/C) | Cs = 2~3Cp | P = Cs·ΔV²·fswCalculation model (updates with parameters)
Bode plot (magnitude / phase, updates with parameters)
| Ringing frequency f_ring | 15.92 MHz | f_ring = 1/(2π√(LC)) |
| Stray capacitance Cp | 1 nF | input value |
| Stray inductance L | 100 nH | input value |
| characteristic impedance Z₀ = √(L/C) | 10 Ω | damping resistor design basis |
| Recommended snubber resistor R | 10 Ω | R ≈ Z₀; tune within 0.5–1×Z₀, smaller for stronger damping |
| Recommended snubber capacitor Cs | 2 nF ~ 3 nF | Start at 2–3×Cp (plot uses 2.5×Cp); reduce when loss-sensitive |
| Snubber branch corner frequency | 6.366 MHz | 1/(2πR·Cs); must be well below f_ring to snub |
| Snubber resistor dissipation | 1.625 W | P = Cs·ΔV²·fsw; choose the package with ≥2× margin |
Engineering notes
- Two-frequency method: ① measure ringing f₁ at the switching node; ② parallel a known small Cadd and measure f₂; ③ solve Lp / Cp — more reliable than guessing strays.
- Also applies to relay / thyristor contacts (often start with 100Ω + 100nF); for contacts, put R in series before C to limit inrush.
- The RCD clamp (another tool here) handles flyback leakage spikes; the RC snubber handles ringing and dv/dt — the two can coexist.
FAQ
- What is RC Snubber Design for?
- Ring damping for MOS / relay switching nodes: dual-frequency extraction of strays, with R/C values, loss, and an impedance Bode plot.
- What is the formula for RC Snubber Design?
- Core formula: f_ring = 1/(2π√(LC)) | R = √(L/C) | Cs = 2~3Cp | P = Cs·ΔV²·fsw. The tool returns results instantly using this formula and the selected parameters.
- What engineering notes should I keep in mind when using RC Snubber Design?
- Two-frequency method: ① measure ringing f₁ at the switching node; ② parallel a known small Cadd and measure f₂; ③ solve Lp / Cp — more reliable than guessing strays. Also applies to relay / thyristor contacts (often start with 100Ω + 100nF); for contacts, put R in series before C to limit inrush. The RCD clamp (another tool here) handles flyback leakage spikes; the RC snubber handles ringing and dv/dt — the two can coexist.
Embed this calculator on your site / blog / intranet
Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.