Skip to main content
DD-CAT IDE logoDD-CAT IDE

Online Tools

常用电子 / 电工 / 传感器 / Thermal Design / Mechanics / Thermodynamics / 电磁学Calculate工具

198电子 / 电工 / 嵌入式 / 传感器 / Thermal Design / Mechanics / Thermodynamics / 电磁学High频Calculate器,SVG 图示Calculate模型,填参数即时出结果:Resistance分压、DC-DC 反馈Resistance、TL431 反馈(Flyback / Forward)、PCB 阻抗 / 载流、CAN bits定时、CRC check、4-20mA、NTC / PT100、PLC 模拟量、散热器选型、Battery stringandCharge、Sallen-Key 滤波器、传输线延时、VSWR、motor选型、线路voltage drop、calorie诺效率……

PCB Design

15 tools
PCB Design

PCB Trace Current Capacity

Safe current from width, copper weight, and allowed temperature rise per IPC-2221, plus trace resistance / drop.

I = k · ΔT^0.44 · A^0.725 (A in mil²)used 65 times
PCB Design

PCB Trace Width for Current

Work backwards per IPC-2221: from current and allowed rise, find minimum width rounded to 0.1mm.

A = (I/k)^(1/0.725) | W = A / Tused 38 times
PCB Design

PCB Characteristic Impedance

Quick characteristic impedance for microstrip / symmetric stripline (IPC-2141); check before routing USB, Ethernet, or RF traces.

microstrip Z0 = 87/√(εr+1.41) · ln[5.98h/(0.8w+t)]used 5 times
PCB Design

PCB Trace Resistance

DC resistance, drop, and dissipation from length, width, and copper weight — essential for long supply / sense traces.

R = ρ · L / (W · T), ρcopper = 1.724e-8 Ω·mused 69 times
PCB Design

Via current / resistance

Via resistance and current capacity from drill, board thickness, and plating — check before switching layers at high current.

R = ρ·L/A | A = π/4·[(d+2t)² − d²]used 10 times
PCB Design

PCB Differential Pair Impedance

Edge-coupled differential impedance from width, spacing, and dielectric thickness; compare to 90/100/120Ω targets with tuning hints.

Zdiff = 2·Z0·(1 − k·e^(−c·s/h))|microstrip k=0.48 c=0.96, stripline k=0.34 c=2.9used 63 times
PCB Design

PCB Spiral Inductor Designer

Planar spiral coil: inductance, DC resistance, rough Q, self-resonance, and current from turns, width, spacing, and outer diameter.

L = K1·µ0·n²·d_avg/(1+K2·ρ)|d_in = d_out − 2n·w − (2n−1)·sused 24 times
PCB Design

PCB Planar Transformer Designer

Planar transformer design: turns from the volt-second equation, rounded ratio, flux check, winding width/layers, and copper loss.

N1 ≥ Vin·D/(k_vs·f·B·Ae)|n = N2/N1 = Vout/(k_v·Vin·D)used 16 times
PCB Design

NFC PCB Antenna Design

13.56MHz PCB NFC antenna: square spiral inductance, resonance tuning capacitor (E6), Q and damping resistor, and read-range estimate.

L modified Wheeler|C = 1/((2πf)²·L) − Cp|H(d) = n·I·a²/(2(a²+d²)^1.5)used 41 times
PCB Design

WiFi/BT PCB Antenna Design

2.4GHz PCB antenna: λ/4 inverted-F (IFA) arm length or half-wave patch W/L/feed inset, with 50Ω feed width and clearance notes.

λ/4 arm = c/(4f·√εeff)|patch W = c/(2f)·√(2/(εr+1)), L = c/(2f·√εeff) − 2ΔLused 15 times
PCB Design

SMT Copper Shim (Current Shunt) Calculator

A high-current trace can be reinforced by a copper shim soldered onto the PCB: from the shim size, parallel copper foil and solder-joint resistance it computes equivalent resistance, shim/copper current sharing, ampacity, voltage drop, losses and temperature rise — or back-solves the minimum shim thickness for a given current.

R = ρ(T)·L/(W·t) | R_eq = R_shim ∥ R_pcb | I = √(h·A_surf·ΔT/(R_eq + R_solder))used 1 times
PCB Design

Antenna Length Calculator (λ/4 · λ/2 · 5/8λ)

Compute free-space wavelength and the practical size of monopole, dipole, whip and loop antennas, including the velocity factor — before you cut wire or draw a PCB antenna.

λ = 300/f(MHz) m | monopole ≈ λ/4 × velocity factorused 2 times
PCB Design

PCB Panel Utilization Calculator

From board size, panel size and spacing, get the number of boards per panel and the area utilisation — check it before quoting or designing V-cuts.

n = ⌊(L+spacing)/(l+spacing)⌋ × ⌊(W+spacing)/(w+spacing)⌋used 4 times
PCB Design

Stencil Area Ratio & Paste Volume

From pad size and stencil thickness, compute area ratio, aspect ratio and paste volume to predict insufficient paste on fine-pitch pads — a DFM self-check.

Area ratio = W·L / [2T(W+L)] ≥ 0.66 | aspect ratio = W/T ≥ 1.5
PCB Design

Substrate Current Capacity Calculator (AlN vs FR4)

Compares the maximum current a trace of the same geometry can carry on an aluminium-nitride versus an FR4 substrate using a 1D conduction model, and spells out voltage drop, drop ratio and dissipation — AlN’s high thermal conductivity raises the current capacity by an order of magnitude.

I = W·√(ΔT·k·T/(ρ·h)),ΔV = I·ρ·L/(W·t),δ = √(ρ/(π·f·μ))