Skip to main content
DD-CAT IDE logoDD-CAT IDE

WiFi/BT PCB Antenna Design

Favoriteused 15 times

2.4GHz PCB antenna: λ/4 inverted-F (IFA) arm length or half-wave patch W/L/feed inset, with 50Ω feed width and clearance notes.

Key points

WiFi/BT PCB Antenna Design: 2.4GHz PCB antenna: λ/4 inverted-F (IFA) arm length or half-wave patch W/L/feed inset, with 50Ω feed width and clearance notes. Formula: λ/4 arm = c/(4f·√εeff)|patch W = c/(2f)·√(2/(εr+1)), L = c/(2f·√εeff) − 2ΔL. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. PCB λ/4 antennas vary a lot: prototype with ±2mm around the initial arm length, measure resonance with a VNA and trim the tip; place the IFA at the board edge with the arm facing out. Keep ≥3h clearance (no copper or traces) below and around the arm; keep batteries / metal / shields ≥10mm away, or it detunes and efficiency plummets.

Inputs

λ/4 arm = c/(4f·√εeff)|patch W = c/(2f)·√(2/(εr+1)), L = c/(2f·√εeff) − 2ΔL

Calculation model (updates with parameters)

GND copper pourClearance zone (no copper)50Ω feedgλ/4 = 22.2 mmλ0 = 122 mm · λg = 89 mm
Free-space wavelength λ0122.4 mm
in-dielectric wavelength λg88.8 mm
Radiating arm length (λ/4)22.2 mm
Ground stub and coupling gapg ≈ 1~2 mm
50Ω feed width3.02 mm
⚠ Keep ≥3h clearance below and around the antenna arm (no copper, traces, or battery metal); place the arm toward the board edge and match by trimming its length.

Engineering notes

  • PCB λ/4 antennas vary a lot: prototype with ±2mm around the initial arm length, measure resonance with a VNA and trim the tip; place the IFA at the board edge with the arm facing out.
  • Keep ≥3h clearance (no copper or traces) below and around the arm; keep batteries / metal / shields ≥10mm away, or it detunes and efficiency plummets.
  • BT and 2.4G WiFi can share one 2.45GHz antenna; 5G WiFi needs a separate 5.5GHz antenna or a dual-band design.
  • FR-4 loss is significant at 5.8GHz (tanδ≈0.02); consider Rogers or an external antenna at high bands; OTA/conducted tests are required before production.

FAQ

What is WiFi/BT PCB Antenna Design for?
2.4GHz PCB antenna: λ/4 inverted-F (IFA) arm length or half-wave patch W/L/feed inset, with 50Ω feed width and clearance notes.
What is the formula for WiFi/BT PCB Antenna Design?
Core formula: λ/4 arm = c/(4f·√εeff)|patch W = c/(2f)·√(2/(εr+1)), L = c/(2f·√εeff) − 2ΔL. The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using WiFi/BT PCB Antenna Design?
PCB λ/4 antennas vary a lot: prototype with ±2mm around the initial arm length, measure resonance with a VNA and trim the tip; place the IFA at the board edge with the arm facing out. Keep ≥3h clearance (no copper or traces) below and around the arm; keep batteries / metal / shields ≥10mm away, or it detunes and efficiency plummets. BT and 2.4G WiFi can share one 2.45GHz antenna; 5G WiFi needs a separate 5.5GHz antenna or a dual-band design. FR-4 loss is significant at 5.8GH…
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.