Resistor Voltage Divider
上臂 R1 接Input、下臂 R2 接地:既可按给定 R1/R2 算Output voltage,也可由Input量程and ADC 参数枚举StdResistance,给出Source impedance合适的采样最佳组合。
Key points
Resistor Voltage Divider: 上臂 R1 接Input、下臂 R2 接地:既可按给定 R1/R2 算Output voltage,也可由Input量程and ADC 参数枚举StdResistance,给出Source impedance合适的采样最佳组合。 Formula: Vout = Vin × R2 / (R1 + R2) | ADC: R2/(R1+R2) = Vref(1−Margin)/Vin,max. Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. The standard divider uses the no-load formula; the next stage’s input impedance must be ≥ 10×R2, otherwise recalculate as a parallel combination. ADC mode: divider ratio = Vref×(1−headroom) / Vin,max, then enumerate R1/R2 from the standard series. The constraint is ADC-side source impedance R1∥R2 ≤ the datasheet limit, balancing sample/hold charging against dissipation.
Inputs
Vout = Vin × R2 / (R1 + R2) | ADC: R2/(R1+R2) = Vref(1−Margin)/Vin,maxCalculation model (updates with parameters)
| Output voltage Vout | 495 mV | No-load value at standard resistors; loading divides further |
| [Rounded] R1 / R2 | 9.1 kΩ / 1 kΩ | Input 9 kΩ / 1 kΩ, by E24 nearest value |
| [Rounded] Vout deviation | -0.99% | No-load output relative to raw inputs |
| Divider current I | 495 µA | Vin/(R1+R2) |
| R1 dissipation | 2.23 mW | Choose 2× headroom or more |
| R2 dissipation | 245.1 µW |
Engineering notes
- The standard divider uses the no-load formula; the next stage’s input impedance must be ≥ 10×R2, otherwise recalculate as a parallel combination.
- ADC mode: divider ratio = Vref×(1−headroom) / Vin,max, then enumerate R1/R2 from the standard series. The constraint is ADC-side source impedance R1∥R2 ≤ the datasheet limit, balancing sample/hold charging against dissipation.
- Source impedance is R1∥R2 (Thevenin equivalent): a SAR ADC charges its internal sample capacitor at each conversion, and too high a source impedance causes low readings and more crosstalk — lower the sample rate or add a small capacitor at the ADC pin if needed.
- Resistor tolerance (e.g. ±1%) turns directly into ratio error; for high accuracy use E96 and tight-tolerance resistors, and calibrate the gain with a two-point software calibration.
- The error analysis adds worst cases linearly (resistor tolerance + reference tolerance + ADC offset/gain/INL) and gives an RSS typical value; resistors of the same type and batch partially cancel their tempco, while wiring and buffer offset must be added separately.
FAQ
- What is Resistor Voltage Divider for?
- 上臂 R1 接Input、下臂 R2 接地:既可按给定 R1/R2 算Output voltage,也可由Input量程and ADC 参数枚举StdResistance,给出Source impedance合适的采样最佳组合。
- What is the formula for Resistor Voltage Divider?
- Core formula: Vout = Vin × R2 / (R1 + R2) | ADC: R2/(R1+R2) = Vref(1−Margin)/Vin,max. The tool returns results instantly using this formula and the selected parameters.
- What engineering notes should I keep in mind when using Resistor Voltage Divider?
- The standard divider uses the no-load formula; the next stage’s input impedance must be ≥ 10×R2, otherwise recalculate as a parallel combination. ADC mode: divider ratio = Vref×(1−headroom) / Vin,max, then enumerate R1/R2 from the standard series. The constraint is ADC-side source impedance R1∥R2 ≤ the datasheet limit, balancing sample/hold charging against dissipation. Source impedance is R1∥R2 (Thevenin equivalent): a SAR ADC charges its internal sample capacitor at each c…
Embed this calculator on your site / blog / intranet
Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.