Skip to main content
DD-CAT IDE logoDD-CAT IDE

Buck-Boost step-up/down design

Favoriteused 12 times

Enter design targets (output taken as absolute value, polarity inverted) to get the inductor, input/output capacitors, MOS SOA, gate resistor, and thermal design.

Key points

Buck-Boost step-up/down design: Enter design targets (output taken as absolute value, polarity inverted) to get the inductor, input/output capacitors, MOS SOA, gate resistor, and thermal design. Formula: D = |Vout|/(Vin+|Vout|) | L = Vin·D/(ΔIL·fsw). Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. The inverting Buck-Boost outputs inverted polarity; MOS and diode stress is Vin+|Vout| summed, and both ends use the combined voltage. Also has a right-half-plane zero (lower than Boost), so design the loop conservatively; the input cap sees square-wave current — prefer low ESR.

Inputs

D = |Vout|/(Vin+|Vout|) | L = Vin·D/(ΔIL·fsw)

Calculation model (updates with parameters)

主电路(标注为设计值)

VINCin133.5 nFQ:BVDSS ≥ 60 V · Rds ≤ 124.9 mΩPWM105.7 µHCout122 µFload−VOUTVout = −12.0 VD ≈ 61.0 % | fsw = 200 kHz | ΔIL = 230.8 mA

MOS 安全工作区 SOA(五边界 + 开关负载线,随参数联动)

Rds(on) 欧姆线DC 恒功率 ΔT/θJA脉冲线(×5/×20)BVDSS 电压限Id_rated 电流限开关负载线100 mV1 V10 V100 V100 mA1 A10 AVds(V,对数轴)DC 安全面BVDSS ≥ 60 VId_rated ≈ 6.003 A(假设 2×Id_pk)导通点 234.1 mV / 2.678 A关断点 ≈ 48 V

⚠ 负载线中段 V·I ≈ 32.13 W,超出 10µs 示意边界(16.67 W)——直线为保守包络,实际开关轨迹呈梯形且远窄于此,请按候选 MOS 手册 SOA 复核。

绿色 = DC 安全面(Rds(on) 欧姆线 ∩ 恒功率 ΔT/θJA ∩ 电流定额 ∩ BVDSS);灰虚线 = 1ms / 10µs 单脉冲(Zth 典型倍率 ×5 / ×20,示意); 红色负载线 = 导通点(Id_pk·Rds)→ 关断点(Vds_stress,漏电流级)的开关轨迹,稳态导通段须落在绿区内,瞬时段按脉冲边界校验。

Bode plot (magnitude / phase, updates with parameters)

Gvd(buckboost) duty→output-40-30-20-10010203040-450°-405°-360°-315°-270°-225°-180°100 Hz1 kHz10 kHz100 kHzf (log axis)dBphase907.1 Hzcrossover ≈ 6.799 kHzphase -374°CCM voltage-mode small-signal approximation (with ESR zero)and the right-half-plane zero — keep crossover below 1/5 of it)
[Control mode]CCM (continuous)
[Duty] max D (@Vin_min)61.0 %
[Duty] min D (@Vin_max)25.8 %
[Inductor] recommended inductance105.7 µH
[Inductor] actual ripple current230.8 mA(23%)
[Inductor] peak current (Isat ≥ 1.2×)2.678 A
[Inductor] RMS current2.563 A
[Inductor] DCR limit (1% loss)18.27 mΩ
[Output cap] capacitance122 µF
[Output cap] ESR limit9.336 mΩ
[Output cap] RMS current1.25 A
[Input cap] ripple voltage target1080 mV
[Input cap] capacitance133.5 nF
[Input cap] ESR limit2.34 Ω
[Input cap] RMS current66.62 mA
[MOS] Vds rating requirement (with margin)60 V
[MOS] peak current Id_pk2.678 A
[MOS] conduction current Id_rms2.001 A
[MOS] Rds(on) limit (60% loss budget)124.9 mΩ
[MOS] Qg limit (1% efficiency budget)60 nC
[Gate resistor] recommended Rg15.0 Ω
[Gate resistor] switching edges t_r ≈ t_f24 ns
[Gate resistor] peak drive current (Miller plateau)333.3 mA
[Gate resistor] average drive current6 mA
[Gate resistor] drive power60 mW
[Thermal] allowed total loss833.3 mW
[Thermal] conduction loss (at 0.7×Rds_max)350 mW
[Thermal] switching loss590.4 mW
[Thermal] required θJA53 °C/W
[SOA] operating point (Vds_stress × IL_pk)48 V × 2.678 A
[Async rectifier] diode reverse voltage48 V
[Async rectifier] average current / conduction loss1 A · 500 mW
⚠ Thermal check failed: temperature target requires θJA ≤ 53 °C/W; use a lower-θJA package or redesign at lower frequency.

Engineering notes

  • The inverting Buck-Boost outputs inverted polarity; MOS and diode stress is Vin+|Vout| summed, and both ends use the combined voltage.
  • Also has a right-half-plane zero (lower than Boost), so design the loop conservatively; the input cap sees square-wave current — prefer low ESR.

FAQ

What is Buck-Boost step-up/down design for?
Enter design targets (output taken as absolute value, polarity inverted) to get the inductor, input/output capacitors, MOS SOA, gate resistor, and thermal design.
What is the formula for Buck-Boost step-up/down design?
Core formula: D = |Vout|/(Vin+|Vout|) | L = Vin·D/(ΔIL·fsw). The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using Buck-Boost step-up/down design?
The inverting Buck-Boost outputs inverted polarity; MOS and diode stress is Vin+|Vout| summed, and both ends use the combined voltage. Also has a right-half-plane zero (lower than Boost), so design the loop conservatively; the input cap sees square-wave current — prefer low ESR.
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.