Skip to main content
DD-CAT IDE logoDD-CAT IDE

Buck step-down design

Favoriteused 2 times

Enter design targets (voltage range / temperature rise / ripple / mode / frequency) to get the inductor, input/output capacitors, MOS SOA, gate resistor, and thermal design in one go.

Key points

Buck step-down design: Enter design targets (voltage range / temperature rise / ripple / mode / frequency) to get the inductor, input/output capacitors, MOS SOA, gate resistor, and thermal design in one go. Formula: D = Vout/Vin | L = (Vin−Vout)·D/(ΔIL·fsw). Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. Loss budget: 60% conduction, 40% switching; once a specific MOS is chosen, recalculate with its Rds/Qg. Synchronous rectification (Vf = 0) removes diode loss with the same duty cycle; for light-load efficiency, consider the minimum inductor current in forced CCM.

Inputs

D = Vout/Vin | L = (Vin−Vout)·D/(ΔIL·fsw)

Calculation model (updates with parameters)

主电路(标注为设计值)

VINCin2.115 µFQ:BVDSS ≥ 45 V · Rds ≤ 193.2 mΩPWMVf=0.5VL50.61 µHCout11.54 µFloadVOUTD ≈ 64.7 % | fsw = 200 kHz | ΔIL = 461.5 mA

MOS 安全工作区 SOA(五边界 + 开关负载线,随参数联动)

Rds(on) 欧姆线DC 恒功率 ΔT/θJA脉冲线(×5/×20)BVDSS 电压限Id_rated 电流限开关负载线100 mV1 V10 V100 V100 mA1 A10 AVds(V,对数轴)DC 安全面BVDSS ≥ 45 VId_rated ≈ 4.826 A(假设 2×Id_pk)导通点 301.7 mV / 2.231 A关断点 ≈ 36 V

⚠ 负载线中段 V·I ≈ 20.08 W,超出 10µs 示意边界(16.67 W)——直线为保守包络,实际开关轨迹呈梯形且远窄于此,请按候选 MOS 手册 SOA 复核。

绿色 = DC 安全面(Rds(on) 欧姆线 ∩ 恒功率 ΔT/θJA ∩ 电流定额 ∩ BVDSS);灰虚线 = 1ms / 10µs 单脉冲(Zth 典型倍率 ×5 / ×20,示意); 红色负载线 = 导通点(Id_pk·Rds)→ 关断点(Vds_stress,漏电流级)的开关轨迹,稳态导通段须落在绿区内,瞬时段按脉冲边界校验。

Bode plot (magnitude / phase, updates with parameters)

Gvd(buck) duty→output-80-60-40-2002040-180°-135°-90°-45°0°1 kHz10 kHz100 kHz1 MHzf (log axis)dBphase6.586 kHzcrossover ≈ 31.45 kHzphase -163°CCM voltage-mode small-signal approximation (with ESR zero))
[Control mode]CCM (continuous)
[Duty] max D (@Vin_min)64.7 %
[Duty] min D (@Vin_max)15.1 %
[Inductor] recommended inductance50.61 µH
[Inductor] actual ripple current461.5 mA(23%)
[Inductor] peak current (Isat ≥ 1.2×)2.231 A
[Inductor] RMS current2 A
[Inductor] DCR limit (1% loss)25 mΩ
[Output cap] capacitance11.54 µF
[Output cap] ESR limit54.17 mΩ
[Output cap] RMS current133.2 mA
[Input cap] ripple voltage target1080 mV
[Input cap] capacitance2.115 µF
[Input cap] ESR limit242.1 mΩ
[Input cap] RMS current955.8 mA
[MOS] Vds rating requirement (with margin)45 V
[MOS] peak current Id_pk2.231 A
[MOS] conduction current Id_rms1.609 A
[MOS] Rds(on) limit (60% loss budget)193.2 mΩ
[MOS] Qg limit (1% efficiency budget)50 nC
[Gate resistor] recommended Rg15.0 Ω
[Gate resistor] switching edges t_r ≈ t_f24 ns
[Gate resistor] peak drive current (Miller plateau)333.3 mA
[Gate resistor] average drive current6 mA
[Gate resistor] drive power60 mW
[Thermal] allowed total loss833.3 mW
[Thermal] conduction loss (at 0.7×Rds_max)350 mW
[Thermal] switching loss345.6 mW
[Thermal] required θJA72 °C/W
[SOA] operating point (Vds_stress × IL_pk)36 V × 2.231 A
[Async rectifier] diode reverse voltage36 V
[Async rectifier] average current / conduction loss705.9 mA · 352.9 mW

Engineering notes

  • Loss budget: 60% conduction, 40% switching; once a specific MOS is chosen, recalculate with its Rds/Qg.
  • Synchronous rectification (Vf = 0) removes diode loss with the same duty cycle; for light-load efficiency, consider the minimum inductor current in forced CCM.

FAQ

What is Buck step-down design for?
Enter design targets (voltage range / temperature rise / ripple / mode / frequency) to get the inductor, input/output capacitors, MOS SOA, gate resistor, and thermal design in one go.
What is the formula for Buck step-down design?
Core formula: D = Vout/Vin | L = (Vin−Vout)·D/(ΔIL·fsw). The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using Buck step-down design?
Loss budget: 60% conduction, 40% switching; once a specific MOS is chosen, recalculate with its Rds/Qg. Synchronous rectification (Vf = 0) removes diode loss with the same duty cycle; for light-load efficiency, consider the minimum inductor current in forced CCM.
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.