Skip to main content
DD-CAT IDE logoDD-CAT IDE

Boost step-up design

Favoriteused 30 times

Enter design targets to get the inductor (with RHP-zero check band), input/output capacitors, MOS SOA, gate resistor, and thermal design.

Key points

Boost step-up design: Enter design targets to get the inductor (with RHP-zero check band), input/output capacitors, MOS SOA, gate resistor, and thermal design. Formula: D = 1−Vin/Vout | L = Vin·D/(ΔIL·fsw). Enter parameters on the DD-CAT IDE online tool page to get results instantly, with a calculation-model diagram that updates with the inputs. Boost has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ or transients will diverge. At power-on the inductor passes straight to the output; soft-start / inrush limiting is needed. Efficiency collapses at high duty cycle.

Inputs

D = 1−Vin/Vout | L = Vin·D/(ΔIL·fsw)

Calculation model (updates with parameters)

主电路(标注为设计值)

VINCin300.5 nFL116.7 µHPWMQ ≥ 29 VVf=0.5VCout134.7 µFloadVOUTD ≈ 67.3 % | fsw = 200 kHz | ΔIL = 230.8 mA

MOS 安全工作区 SOA(五边界 + 开关负载线,随参数联动)

Rds(on) 欧姆线DC 恒功率 ΔT/θJA脉冲线(×5/×20)BVDSS 电压限Id_rated 电流限开关负载线100 mV1 V10 V100 V100 mA1 A10 AVds(V,对数轴)DC 安全面BVDSS ≥ 29 VId_rated ≈ 6.356 A(假设 2×Id_pk)导通点 363.2 mV / 3.178 A关断点 ≈ 25 V

⚠ 负载线中段 V·I ≈ 19.86 W,超出 10µs 示意边界(16.67 W)——直线为保守包络,实际开关轨迹呈梯形且远窄于此,请按候选 MOS 手册 SOA 复核。

绿色 = DC 安全面(Rds(on) 欧姆线 ∩ 恒功率 ΔT/θJA ∩ 电流定额 ∩ BVDSS);灰虚线 = 1ms / 10µs 单脉冲(Zth 典型倍率 ×5 / ×20,示意); 红色负载线 = 导通点(Id_pk·Rds)→ 关断点(Vds_stress,漏电流级)的开关轨迹,稳态导通段须落在绿区内,瞬时段按脉冲边界校验。

Bode plot (magnitude / phase, updates with parameters)

Gvd(boost) duty→output-40-30-20-10010203040-270°-225°-180°-135°-90°-45°0°100 Hz1 kHz10 kHz100 kHzf (log axis)dBphase634.6 Hzcrossover ≈ 4.775 kHzphase -208°CCM voltage-mode small-signal approximation (with ESR zero)and the right-half-plane zero — keep crossover below 1/5 of it)
[Control mode]CCM (continuous)
[Duty] max D (@Vin_min)67.3 %
[Duty] min D (@Vin_max)34.7 %
[Inductor] recommended inductance116.7 µH
[Inductor] actual ripple current230.8 mA(23%)
[Inductor] peak current (Isat ≥ 1.2×)3.178 A
[Inductor] RMS current3.063 A
[Inductor] DCR limit (1% loss)25.59 mΩ
[Output cap] capacitance134.7 µF
[Output cap] ESR limit7.867 mΩ
[Output cap] RMS current1.436 A
[Input cap] ripple voltage target480 mV
[Input cap] capacitance300.5 nF
[Input cap] ESR limit1.04 Ω
[Input cap] RMS current66.62 mA
[MOS] Vds rating requirement (with margin)29 V
[MOS] peak current Id_pk3.178 A
[MOS] conduction current Id_rms1.75 A
[MOS] Rds(on) limit (60% loss budget)163.3 mΩ
[MOS] Qg limit (1% efficiency budget)120 nC
[Gate resistor] recommended Rg15.0 Ω
[Gate resistor] switching edges t_r ≈ t_f24 ns
[Gate resistor] peak drive current (Miller plateau)333.3 mA
[Gate resistor] average drive current6 mA
[Gate resistor] drive power60 mW
[Thermal] allowed total loss833.3 mW
[Thermal] conduction loss (at 0.7×Rds_max)350 mW
[Thermal] switching loss360.2 mW
[Thermal] required θJA70 °C/W
[SOA] operating point (Vds_stress × IL_pk)25 V × 3.178 A
[Async rectifier] diode reverse voltage40 V
[Async rectifier] average current / conduction loss1 A · 500 mW

Engineering notes

  • Boost has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ or transients will diverge.
  • At power-on the inductor passes straight to the output; soft-start / inrush limiting is needed. Efficiency collapses at high duty cycle.

FAQ

What is Boost step-up design for?
Enter design targets to get the inductor (with RHP-zero check band), input/output capacitors, MOS SOA, gate resistor, and thermal design.
What is the formula for Boost step-up design?
Core formula: D = 1−Vin/Vout | L = Vin·D/(ΔIL·fsw). The tool returns results instantly using this formula and the selected parameters.
What engineering notes should I keep in mind when using Boost step-up design?
Boost has a right-half-plane zero (RHPZ); keep the loop crossover below 1/5 of the RHPZ or transients will diverge. At power-on the inductor passes straight to the output; soft-start / inrush limiting is needed. Efficiency collapses at high duty cycle.
ShareWeiboXLinkedIn
Embed this calculator on your site / blog / intranet

Copy the snippet below into any HTML-capable page — visitors get the same live calculator, styling included.