Skip to main content
DD-CAT IDE logoDD-CAT IDE

Article · Tech Insights

Thevenin's Theorem Through a Black-Box Castle: A Fairy-Tale Guide to Vth and Rth, with Derivations and Three Pitfalls

Favorite

When mentoring newcomers, I repeatedly find that people can recite Thévenin's theorem but can't apply it—open-circuit voltage, the lights-out method for internal resistance, and computing the load after the equivalent are all just moves on paper. I use a fairy-tale black-box castle to tie three things together: measure the water level at the gate to get Vth, put the magic sources to sleep to get Rth, and fold the whole castle into one water pump plus one rough pipe. Then I add why it must hold (the port V-I is a straight line) and the three easiest pitfalls (internal power can't be computed from the equivalent circuit, nonlinearity, and negative resistance).

ShareWeiboXLinkedIn

Key points

Thévenin's theorem states that any linear two-terminal network can be replaced by a voltage source Vth in series with a resistor Rth: Vth is the open-circuit port voltage, and Rth is the equivalent resistance seen from the port after all independent sources are set to zero (voltage sources shorted, current sources opened). Using a fairy-tale black-box castle as a metaphor, the recipe has three steps: measure the open-circuit voltage to get Vth, turn off the sources to find Rth, then connect the load and apply the divider formula V_L = Vth·R_L/(Rth+R_L). The theorem holds because a linear network's port V-I relationship is a straight line whose intercept is the open-circuit voltage and whose slope is −Rth, so Rth also equals Vth/Isc (short-circuit method). Watch out for three pitfalls: the equivalent cannot compute internal power or efficiency, nonlinear devices require small-signal linearization around the operating point, and Rth can be negative when controlled sources are present. In practice it explains sensor output impedance, maximum power transfer (power peaks at R_L = Rth but efficiency is only 50%), Wheatstone bridge loading, and ADC source-impedance limits.

Thévenin's theorem is the first major hurdle in every circuits course. Everyone can recite the statement—"any linear two-terminal network can be replaced by a voltage source in series with a resistor"—but on a real board, many people still don't know where to measure those two values. When I teach this to newcomers, I made up a fairy tale; after telling it, I have them work through the math by hand, and they rarely forget it afterward. This time I'm writing down the story and the formulas together.

The Story: The Black-Box Castle in Misty Valley

Deep in the forest stands a black-box castle in Misty Valley. How many waterwheels, millstones, or stones are inside, nobody can say for sure—all anyone knows is that the outer wall has two brass studs (what we call the two terminals).

A little fox named Ali carries a bucket to the castle every day to fetch water. It doesn't care what the castle looks like inside; it only cares about two things: If I hook up my waterwheel, how much flow will I get? Will it be dragged down?

The old craftsman Grandpa Brass-Stud says: no need to go inside. I'll teach you three spells out here at the gate, and you can fold the entire castle into "one small water pump + one rough pipe."

Spell One: Connect Nothing, First Measure the Water Level at the Gate

Block the outlet (open circuit), and poke a measuring stick that draws no water into the brass studs—that's an ideal voltmeter.

Vth=VocV_{th} = V_{oc}

This is not an approximation; it's the definition: the value of the Thévenin voltage source is simply the open-circuit voltage at the port. No matter how much is inside the castle, the pressure difference at the gate when nobody is drawing water is exactly that.

Spell Two: Put All the Things That "Spin by Themselves" to Sleep

The castle contains two kinds of self-moving magic: constant-pressure machines (voltage sources) and constant-flow channels (current sources). To measure how rough the pipe is, you must first make them stop:

  • The pressure machine no longer produces a pressure difference → it becomes an empty pipe running straight through: the voltage source is shorted;
  • The constant-flow channel no longer delivers water → it becomes a fully closed valve: the current source is opened.

Then measure the equivalent resistance looking into the two brass studs—that is the Thévenin internal resistance:

Rth=Req∣voltage sources shorted, current sources openedR_{th} = R_{eq}\Big|_{\text{voltage sources shorted, current sources opened}}

There's a second version that doesn't require disabling the sources—you just have to dare to short the outlet: measure the short-circuit current IscI_{sc}, then

Rth=VocIscR_{th} = \frac{V_{oc}}{I_{sc}}

The two versions must agree—and later I'll explain why.

Spell Three: Fold the Entire Castle into a Pump Plus a Pipe

  any linear two-terminal network  ≡  Vth in series with Rth  \boxed{\;\text{any linear two-terminal network} \;\equiv\; V_{th} \text{ in series with } R_{th}\;}

After connecting the load RLR_L (Ali's waterwheel):

IL=VthRth+RL,VL=Vth⋅RLRth+RLI_L = \frac{V_{th}}{R_{th}+R_L},\qquad V_L = V_{th}\cdot\frac{R_L}{R_{th}+R_L}

The voltage-divider expression makes it clear: RthR_{th} is the castle's own roughness, and RLR_L is your waterwheel. To get more water (VLV_L close to VthV_{th}), either make RL≫RthR_L \gg R_{th}, or find a way to lower the castle's RthR_{th}. From now on, "how much the voltage sags under load" is just one division.

Trial: Hand Calculation on the Voltage-Divider Castle

The first castle Ali meets is simple: a 12 V12\,\mathrm{V} pressure machine inside, in series with R1=6 kΩR_1 = 6\,\mathrm{k\Omega}, with R2=3 kΩR_2 = 3\,\mathrm{k\Omega} in parallel to ground, and the two brass studs taken across R2R_2.

Step one, open-circuit voltage (nothing connected to R2R_2):

Vth=12×3 k6 k+3 k=4 VV_{th} = 12 \times \frac{3\,\mathrm{k}}{6\,\mathrm{k}+3\,\mathrm{k}} = 4\ \mathrm{V}

Step two, measure the internal resistance after lights-out (the 12 V12\,\mathrm{V} source is shorted, so R1R_1 and R2R_2 become parallel):

Rth=6 k∥3 k=6×36+3 k=2 kΩR_{th} = 6\,\mathrm{k} \parallel 3\,\mathrm{k} = \frac{6\times3}{6+3}\,\mathrm{k} = 2\ \mathrm{k\Omega}

Step three, connect the RL=2 kΩR_L = 2\,\mathrm{k\Omega} waterwheel:

VL=4×22+2=2 V,IL=42+2 mA=1 mAV_L = 4 \times \frac{2}{2+2} = 2\ \mathrm{V},\qquad I_L = \frac{4}{2+2}\,\mathrm{mA} = 1\ \mathrm{mA}

Now compute directly on the original circuit to verify equivalence. The 2 k2\,\mathrm{k} load in parallel with R2R_2 gives 1.2 k1.2\,\mathrm{k}, the total current is 12/(6+1.2)=1.667 mA12/(6+1.2) = 1.667\,\mathrm{mA}, and the load gets 1.667×1.2=2 V1.667 \times 1.2 = 2\ \mathrm{V}. Exactly the same—and the equivalent circuit has only two components.

Note an engineering habit: for a bias divider network like R2R_2, the source impedance is exactly R1∥R2R_1 \parallel R_2. When choosing ADC divider resistors, the "maximum source impedance" in the datasheet is exactly this value—the online voltage divider calculator shows it directly.

Why It Must Hold: The Port V-I Is a Straight Line

A fairy tale needs logic. Let VV be the port voltage and II the current flowing out of the port. Since the network contains only linear elements (resistors, controlled sources), the superposition theorem tells us:

V=Voc⏟sources acting alone    −    I Rth⏟external current acting aloneV = \underbrace{V_{oc}}_{\text{sources acting alone}} \;\;-\;\;\underbrace{I\,R_{th}}_{\text{external current acting alone}}

In other words, the port's VV and II always lie on the same straight line: the vertical intercept is VocV_{oc} (I=0I=0, open circuit), the horizontal intercept is IscI_{sc} (V=0V=0, short circuit), and the slope is −Rth-R_{th}.

And the branch "voltage source VthV_{th} in series with resistor RthR_{th}" gives exactly the same V-I relationship, V=Vth−IRthV = V_{th} - I R_{th}. Two points determine a line—so as long as the two ports' VV–II lines coincide, a person outside the gate can never tell which is the real castle and which is the folded version. That is the entire content of Thévenin's theorem, and it explains why Rth=Voc/IscR_{th} = V_{oc}/I_{sc} must equal the value from the lights-out method.

As a bonus we get the Norton version: write that line in current form,

I=Isc−VRth,IN=Isc=VthRthI = I_{sc} - \frac{V}{R_{th}},\qquad I_N = I_{sc} = \frac{V_{th}}{R_{th}}

which is a current source INI_N in parallel with RthR_{th}. Thévenin and Norton are two ways of drawing the same line.

The Three Easiest Pitfalls to Step Into

Pitfall One: You Can Only Compute at the Port, Not Internal Power

This is the most common one in exams and in the field. Look again at the divider castle above with a 2 kΩ2\,\mathrm{k\Omega} load:

Source Output Delivered to Load Internal Loss
Real circuit 12 V×1.667 mA=20 mW12\,\mathrm{V} \times 1.667\,\mathrm{mA} = 20\,\mathrm{mW} 2 V×1 mA=2 mW2\,\mathrm{V}\times1\,\mathrm{mA}=2\,\mathrm{mW} R1R_1 16.7 mW + R2R_2 3 mW = 19.7 mW
Thévenin equivalent 4 V×1 mA=4 mW4\,\mathrm{V} \times 1\,\mathrm{mA} = 4\,\mathrm{mW} 2 mW2\,\mathrm{mW} 2 mW across RthR_{th}

The port voltage and port current are exactly the same, but the internal loss differs by nearly ten times. The equivalent circuit is only a stand-in "as seen from outside the gate"; it compresses all losses inside the castle into a single RthR_{th}. Using it to calculate efficiency, resistor power dissipation, or temperature rise is simply wrong.

Pitfall Two: Nonlinear Elements Can't Be Applied Directly

Diodes, transistors, saturated op-amps, and inductors with hysteresis all have curved port V-I characteristics that no pair of straight lines can fit. The remedy is small-signal linearization around the operating point: find the slope near a given DC operating point to get rth=ΔV/ΔIr_{th} = \Delta V/\Delta I, valid only near that point. That is exactly where the transistor's rer_e and the diode's dynamic resistance come from.

Pitfall Three: RthR_{th} Is Not Necessarily a Positive Resistance

When the network contains controlled sources, the RthR_{th} computed after lights-out can absolutely be negative—negative resistance means the port voltage rises as the current increases, which is precisely the foundation of oscillators, hysteresis comparators, and negative-resistance converters. Also, RthR_{th} generally varies with temperature and operating point; a nominal 2 kΩ is only the value under one set of conditions.

The Fairy Tale's Real-World Versions on a Board

  • Sensor / signal source output impedance: that's its RthR_{th}. If the next stage's input impedance isn't large enough, VL=VthRL/(Rth+RL)V_L = V_{th}R_L/(R_{th}+R_L) immediately takes a hit—that's the entire reason "high-impedance signals need a buffer".

  • Maximum power transfer: optimizing over RLR_L, PLP_L is maximized when RL=RthR_L = R_{th},

    PL,max⁡=Vth24RthP_{L,\max} = \frac{V_{th}^2}{4R_{th}}

    At that point the efficiency is only 50% (half the power burns in RthR_{th}). So RF matching pursues RL=RthR_L = R_{th}, while power-supply design pursues RL≫RthR_L \gg R_{th}—the two goals are exactly opposite.

  • Wheatstone bridge: when unbalanced, the Thévenin voltage at the output is the voltage difference between the bridge-arm midpoints, and RthR_{th} is the equivalent resistance of the two half-bridges in parallel, R1∥R3+R2∥RxR_1\parallel R_3 + R_2\parallel R_x—the next-stage instrumentation amplifier's high input-impedance requirement exists precisely to suppress the divider error from this RthR_{th}. To practice, change the arm values in the online Wheatstone bridge calculator and watch how these two quantities change.

  • ADC sampling: at the sampling instant, a SAR ADC must charge its internal sampling capacitor; if the source impedance is too high, it can't fully charge and the reading comes out low. The "maximum source impedance" limit in the datasheet is essentially an RC settling problem between RthR_{th} and the sampling time.

Small Exercises for Yourself

  1. Replace the 12 V12\,\mathrm{V} in the trial with 5 V5\,\mathrm{V}, set R1=10 kR_1 = 10\,\mathrm{k} and R2=10 kR_2 = 10\,\mathrm{k}, find VthV_{th} and RthR_{th}, then connect a 10 k10\,\mathrm{k} load to verify. (Answers: 2.5 V2.5\,\mathrm{V}, 5 k5\,\mathrm{k}, 1.67 V1.67\,\mathrm{V})

  2. Add a 1 mA1\,\mathrm{mA} constant-current source in parallel from the divider to ground, and run the lights-out method again—get a feel for what "open-circuiting a current source" really means.

  3. Think it through: why does the internal loss computed from the equivalent circuit come out too small? Hint: in the real circuit, the open-circuited R2R_2 has been leaking current all along.

The three spells are all you need to remember: open-circuit for voltage, lights-out for internal resistance, connect a load for the divider. However complex the castle is inside, the world outside the gate is always "one pump in series with one rough pipe."

Get new articles by email

Enter your email — we notify you about new articles and releases (unsubscribe anytime).

Related reading

Tech Insights

学习泡妞

学习这件事和泡妞是一回事:为什么不想学、学不会、记不住,蒙卦和逻辑学一句话就点破,一切科学简单到只剩一个「咔嗒」声。用一条条对比的方式,把自学讲成泡妞,看完就忘不掉。

Tech Insights

童话版偏置电路:从电阻分压到 ΔV/R 型,把放大器的「待命点」钉住

放大器的本事全看「待命点」钉在哪:钉得偏,信号一大就削顶;钉得飘,电源一抖就全歪。这篇用斜坡上的木桶讲清偏置是什么,再把六代做法一代代推出来:电阻分压 → 二极管接法当小电阻 → 恒流源当无穷大电阻 → 自偏置四管环(为什么必然「要么死要么不定」)→ 源极垫电阻的 ΔV/R 型 → 大电流的 V/R 型。全篇一套 1.8 V / μCox=200 µA/V² 的数字算到底,附四种结构的电源敏感性对照曲线、五个最容易踩的坑和一屏速记卡。

Tech Insights

童话版电流镜:12 种常用接法一次枚举(附公式、速记卡与选型树)

电流镜只有一句话——共用一个栅压,电流按宽长比被抄过去;但"怎么抄得更稳"有十二条常见路。这篇按"比例 / 叠管子 / 加反馈 / 自己造"四类把常用电流镜全部枚举:单管、源极退化、Widlar、共源共栅、高摆幅、多重共源共栅、威尔逊、改进型威尔逊、增益提升 RGC、β 倍乘、有源电流镜、BJT 版,每种都给 R_out、V_out,min、管数和一句"什么时候用它";再配三代摆幅对照、1.8 V·200 µA·±1% 的选型算例、失配与版图规矩、五个实战场景、七条踩坑和一屏速记卡。