Skip to main content
DD-CAT IDE logoDD-CAT IDE

Article · Tech Insights

Sallen-Key Single-Op-Amp Bandpass Filter: Component Selection and Common Pitfalls

Favorite

My notes on designing a 2nd-order single-op-amp Sallen-Key bandpass filter at f0=1kHz and BW=500Hz: from picking capacitor values by gut feeling, to deriving R/C values from the k, Q, and gain relationships, then rounding to standard values and checking GBW.

ShareWeiboXLinkedIn

Key points

For a single-op-amp Sallen-Key bandpass filter, start from the intermediate constant k=2πf0·C1 and work backward to the five resistor values, keeping R1 near 33kΩ and setting C2=C1/2. Gain is coupled to Q: H=(6.5-1/Q)/3, so at Q=2 the gain is about 2× (≈6dB) with R4=R5. For f0=1kHz and BW=500Hz (Q=2), typical standard values are C1=10nF, C2=4.7nF, R1≈33kΩ, R2≈11kΩ, R3≈66kΩ, and R4=R5=10kΩ. Common mistakes include picking C1=100nF by gut feeling (which pushes all resistors down 10×), treating C2 as an equal-value capacitor, and pushing Q too high without precision parts. Above Q=20, use 1% resistors and COG/NPO capacitors, and verify GBW and the slew-rate requirement SR≥2πf0·Vp.

Background: Why I Calculate Parameters Before Picking Up the Soldering Iron

Recently I added a bandpass stage to a sensor signal-conditioning circuit. The requirements were a center frequency f0=1kHz and bandwidth BW=500Hz, which gives Q=f0/BW=2, on a single 5V supply with only one op-amp allowed. My first version picked the capacitor values off the top of my head—C1=C2=100nF—then worked backward to the resistors. The result: at Q=2 the resistors either dropped to a few hundred ohms or soared into the megaohms, bias current and noise crept in together, and the gain was coupled to Q—change one resistor and all three specs drifted at once.

The upside of a single-op-amp Sallen-Key bandpass is a low parts count and high non-inverting input impedance, but its parameters are tightly coupled, and hand-tuning is just too inefficient. Once I sorted out these relationships, I handed the rest of the work to the calculator.

Parameter Relationships: Pick k First, Then Solve for the Five Resistors

In this circuit, the parameter relationships revolve around an intermediate variable k. The tool automatically picks C1 to keep R1 near 33kΩ:

k=2πf0C1k = 2\pi f_0 C_1

Then:

R1=2k,R2=23k,R3=4k,C2=C12R_1=\frac{2}{k},\quad R_2=\frac{2}{3k},\quad R_3=\frac{4}{k},\quad C_2=\frac{C_1}{2}

The gain branch is set by R4/R5, and the gain is tied to Q:

H=6.5−1/Q3,R5=R4H−1H = \frac{6.5 - 1/Q}{3},\quad R_5=\frac{R_4}{H-1}

Take Q=2 as an example: H=(6.5−0.5)/3=2H=(6.5-0.5)/3=2, i.e., an in-band gain of about 2× (roughly 6dB), with R4 and R5 equal. The tool automatically places R5 near 10kΩ. The higher the Q, the slightly lower H becomes: at Q=10, H=(6.5−0.1)/3≈2.13H=(6.5-0.1)/3\approx 2.13. This gain–Q coupling is the easiest thing to overlook, and it's why many people copy feedback resistor values from a reference yet can't get the gain to line up.

Running It Through the Online Calculator

Open the BPF Op-Amp Bandpass Filter Designer (Sallen-Key, single op-amp). I entered f0=1kHz and BW=500Hz for the design conditions; it also accepts high-pass/low-pass corner frequencies fL and fH and converts them. The page returned standard values of roughly: C1=10nF, C2=4.7nF (i.e., C1/2 rounded to the nearest standard value), R1≈33kΩ, R2≈11kΩ, R3≈66kΩ, and R4 and R5 at 10kΩ each. It also gives the actual center frequency, bandwidth, and a Bode plot after rounding, so I don't have to work through tolerance numbers myself. The GBW and slew-rate checks live on the same page: this set of values doesn't demand much op-amp bandwidth, and my 10MHz rail-to-rail part is plenty. If I changed the example to f0=100kHz and Q=20, the bandwidth requirement would surge, and an ordinary low-bandwidth op-amp would fall short.

Conclusions and Common Pitfalls

Based on my measurements, here are my takeaways:

  • Make C1 accommodate the resistor, not the other way around. Keeping R1 near 33kΩ gives a balanced trade-off among noise, bias current, and power consumption. Fixing C1=100nF first pushes all the resistors down by 10×.
  • C2 is not arbitrary. Many low-pass tutorials reach for equal-value capacitors out of habit, but in this bandpass topology C2=C1/2—switching to equal values directly changes Q and gain.
  • Don't be greedy with Q. At Q=2, ordinary 5% resistors and X7R capacitors work fine. If you push Q above 20, switch to 1% resistors and COG/NPO capacitors, or the center frequency and bandwidth will drift.
  • Check the rounding error first. After rounding to standard resistor values, f0 and Q will deviate from the design targets; go by the actual curves the tool provides, and if the deviation is large, switch to E96 values or fine-tune C1.
  • Check the gain before the op-amp. H is coupled to Q, so the feedback resistors must be recalculated from H. When the output swing is large, verify the slew rate: SR≥2πf0VpSR \ge 2\pi f_0 V_p.

A filter never exists in isolation. If you need to suppress low-frequency drift or high-frequency glitches at the input first, you can work out a Sallen-Key low-pass/high-pass to carve out the band. If you want a steeper roll-off, cascade two bandpass stages, or switch to a multiple-feedback (MFB) bandpass topology, which has different component sensitivities. Once the values are computed, cross-check the GBW and slew-rate specs when picking the op-amp—all of these checks are available right on the bandpass calculator page, far faster than the Excel tables I used to fiddle with.

Get new articles by email

Enter your email — we notify you about new articles and releases (unsubscribe anytime).

Related reading

Tech Insights

学习泡妞

学习这件事和泡妞是一回事:为什么不想学、学不会、记不住,蒙卦和逻辑学一句话就点破,一切科学简单到只剩一个「咔嗒」声。用一条条对比的方式,把自学讲成泡妞,看完就忘不掉。

Tech Insights

童话版偏置电路:从电阻分压到 ΔV/R 型,把放大器的「待命点」钉住

放大器的本事全看「待命点」钉在哪:钉得偏,信号一大就削顶;钉得飘,电源一抖就全歪。这篇用斜坡上的木桶讲清偏置是什么,再把六代做法一代代推出来:电阻分压 → 二极管接法当小电阻 → 恒流源当无穷大电阻 → 自偏置四管环(为什么必然「要么死要么不定」)→ 源极垫电阻的 ΔV/R 型 → 大电流的 V/R 型。全篇一套 1.8 V / μCox=200 µA/V² 的数字算到底,附四种结构的电源敏感性对照曲线、五个最容易踩的坑和一屏速记卡。

Tech Insights

童话版电流镜:12 种常用接法一次枚举(附公式、速记卡与选型树)

电流镜只有一句话——共用一个栅压,电流按宽长比被抄过去;但"怎么抄得更稳"有十二条常见路。这篇按"比例 / 叠管子 / 加反馈 / 自己造"四类把常用电流镜全部枚举:单管、源极退化、Widlar、共源共栅、高摆幅、多重共源共栅、威尔逊、改进型威尔逊、增益提升 RGC、β 倍乘、有源电流镜、BJT 版,每种都给 R_out、V_out,min、管数和一句"什么时候用它";再配三代摆幅对照、1.8 V·200 µA·±1% 的选型算例、失配与版图规矩、五个实战场景、七条踩坑和一屏速记卡。