Skip to main content
DD-CAT IDE logoDD-CAT IDE

Article · Tech Insights

Online PCB Trace Width Calculator: Minimum Width by Current and Temperature Rise (IPC-2221)

Favorite

PCB trace width calculator: enter current, copper thickness, allowed temperature rise, and routing layer to work backwards from IPC-2221 to the minimum trace width, rounded to 0.1mm. Includes external vs. internal layer differences, how copper thickness and temperature rise affect width, and a 1A–10A quick reference.

ShareWeiboXLinkedIn

Key points

For a 2A current with 1oz copper, an allowed temperature rise of 10°C, and external-layer routing, the minimum trace width per IPC-2221 is about 0.79mm (rounded to 0.8mm in practice); the same conditions on an internal layer require about 2.04mm. The calculator takes operating current, copper thickness (0.5/1/2/3oz), allowed temperature rise, and layer (external/internal), using I = k·ΔT^0.44·A^0.725 (k=0.048 external, k=0.024 internal) to solve for the required cross-sectional area and round the minimum width up to 0.1mm. Doubling copper thickness from 1oz to 2oz halves the required width (from 0.79mm to 0.39mm at 2A/10°C external), while relaxing ΔT from 10°C to 20°C lowers it from 0.79mm to 0.52mm. The tool outputs values in both mm and mil, plus a recommended width and required area, with a 1A–10A quick-reference table; power trunk traces are recommended at 2× the calculated value, and low-current results should be checked against the fab's minimum trace capability.

How wide does a trace need to be for 2A? The answer isn't simply “the wider the better”: with 1oz copper, an allowed temperature rise of 10°C, and external-layer routing, the minimum trace width is about 0.79mm, rounded to 0.8mm in engineering practice. Later I found an online PCB current-carrying trace width calculator that can work this out backwards—enter current, copper thickness, temperature rise, and routing layer, and it calculates the minimum trace width per IPC-2221 and rounds it to 0.1mm. I've jotted down the usage and a few test runs as notes for future reference.

Tool: https://www.dd-cat.cn/tools/pcb-width

Formula and Approach: Working Backwards from IPC-2221

The current-carrying formula is I = k · ΔT^0.44 · A^0.725, where A is the copper cross-sectional area (in mil²) and ΔT is the allowed temperature rise; k = 0.048 for external layers and k = 0.024 for internal layers (internal layers dissipate heat poorly, so k is only half). The tool works the formula backwards:

  • A = (I / k)^(1/0.725) computes the required cross-sectional area;
  • W = A / T divides by the copper thickness T (1oz = 1.37mil = 34.8µm; 2oz doubles);
  • finally, round the millimeter value up to 0.1mm—better too wide than too narrow.

There are just four inputs: operating current I, copper thickness (0.5 / 1 / 2 / 3oz), allowed temperature rise ΔT, and routing layer (external / internal). Outputs include the minimum trace width (in both mm and mil), a recommended value, the required cross-sectional area, plus a trace cross-section diagram labeled W, T, and I.

External vs. Internal Layers: About 2.6× Difference for the Same Current

For the same 2A, 1oz, and ΔT = 10°C: the external layer minimum width is about 0.79mm, but the internal layer needs 2.04mm. The reason is that internal layers have no convective air cooling, k is only half of the external value, and the required cross-sectional area is about 2.6 times larger.

This difference matters a lot during layout: keep power trunk traces on the outer layer if possible; if you must route them internally, budget roughly 2.6× the width, otherwise the temperature rise will exceed the limit.

Two Direct, Effective Levers: Copper Thickness and Temperature Rise

Doubling Copper Thickness Halves the Width

At 2A, ΔT = 10°C, external layer, 1oz needs 0.79mm, but switching to 2oz needs only 0.39mm. The required cross-sectional area stays the same; doubling copper thickness naturally halves the width. When space is tight and you don't want to add layers, 2oz copper is a common solution.

Relaxing the Temperature Rise Also Reduces Width

At 2A, 1oz, external layer, relaxing ΔT from 10°C to 20°C lowers the width from 0.79mm to 0.52mm, at the cost of a hotter trace. The choice of ΔT depends on ambient temperature and lifetime requirements; the tool's default 10°C is a fairly conservative baseline.

A Small Detail: Rounding to 0.1mm

The calculated minimum width is often not a multiple of 0.1mm, so the tool rounds up. For example, at 1A, 1oz, external layer, the minimum is 0.30mm, and the rounded recommendation is 0.4mm. Rounding down seems to save a little space, but it eliminates the current margin—don't cut corners here.

Quick Reference for Common Currents (ΔT = 10°C)

CurrentExternal 1ozInternal 1ozExternal 2oz
1A0.4mm0.8mm0.2mm
2A0.8mm2.1mm0.4mm
3A1.4mm3.6mm0.7mm
5A2.8mm7.3mm1.4mm
10A7.3mm18.9mm3.7mm

The table above shows the tool's recommended values (already rounded to 0.1mm). At the 10A level, routing a 7mm-wide trace is no longer practical—in practice you'd use copper pours with via arrays or go straight to a solid power plane.

A Few Notes

  • Consider doubling power trunk traces: the tool gives the minimum width that meets the temperature rise; routing power trunk traces at 2× the calculated value is safer. When space is tight, switch to copper pour + via arrays.
  • Watch the fab's minimum trace width: low-current calculations may come in below 0.2mm, so verify the PCB manufacturer's minimum trace width/spacing capability first.
  • IPC-2221 is an empirical model: for long-term full load or high-temperature environments, add at least 30% margin on top of the result.
  • Don't mix mil and mm: the tool gives both mm and mil, and 1oz = 1.37mil = 34.8µm—be careful with units when converting.

Conclusion

The hard part of current-carrying trace width isn't the formula—it's the three steps of working backwards, rounding, and accounting for internal vs. external layer differences. This tool handles all three at once. I run it before routing to fix the power trunk width, then move into the EDA to route. The link is saved in my bookmarks, alongside the differential impedance and feedback resistor tools.

Get new articles by email

Enter your email — we notify you about new articles and releases (unsubscribe anytime).

Related reading

Tech Insights

学习泡妞

学习这件事和泡妞是一回事:为什么不想学、学不会、记不住,蒙卦和逻辑学一句话就点破,一切科学简单到只剩一个「咔嗒」声。用一条条对比的方式,把自学讲成泡妞,看完就忘不掉。

Tech Insights

童话版偏置电路:从电阻分压到 ΔV/R 型,把放大器的「待命点」钉住

放大器的本事全看「待命点」钉在哪:钉得偏,信号一大就削顶;钉得飘,电源一抖就全歪。这篇用斜坡上的木桶讲清偏置是什么,再把六代做法一代代推出来:电阻分压 → 二极管接法当小电阻 → 恒流源当无穷大电阻 → 自偏置四管环(为什么必然「要么死要么不定」)→ 源极垫电阻的 ΔV/R 型 → 大电流的 V/R 型。全篇一套 1.8 V / μCox=200 µA/V² 的数字算到底,附四种结构的电源敏感性对照曲线、五个最容易踩的坑和一屏速记卡。

Tech Insights

童话版电流镜:12 种常用接法一次枚举(附公式、速记卡与选型树)

电流镜只有一句话——共用一个栅压,电流按宽长比被抄过去;但"怎么抄得更稳"有十二条常见路。这篇按"比例 / 叠管子 / 加反馈 / 自己造"四类把常用电流镜全部枚举:单管、源极退化、Widlar、共源共栅、高摆幅、多重共源共栅、威尔逊、改进型威尔逊、增益提升 RGC、β 倍乘、有源电流镜、BJT 版,每种都给 R_out、V_out,min、管数和一句"什么时候用它";再配三代摆幅对照、1.8 V·200 µA·±1% 的选型算例、失配与版图规矩、五个实战场景、七条踩坑和一屏速记卡。