Skip to main content
DD-CAT IDE logoDD-CAT IDE

Article · Tech Insights

Centripetal Force Calculator Usage Notes: F=mv²/r Parameter Selection and Common Mistakes

Favorite

Notes from using a centripetal force calculator (F=mv²/r) to verify a centrifugal fixture on a rotary stage: three common pitfalls—rpm to rad/s conversion, diameter vs. radius, and mass units—plus a hand-calculated 400 N example and a 1.5–2× safety factor recommendation for part selection.

ShareWeiboXLinkedIn

Key points

The centripetal force calculator checks rotating parts using F=mv²/r or F=mω²r. The three easiest mistakes are: convert rpm to angular velocity first (ω=2πn/60), divide diameter by 2 to get radius, and convert mass to kilograms (SI units). For mass 2 kg, linear velocity 10 m/s, and radius 0.5 m, the force is F=2×10²/0.5=400 N with centripetal acceleration a=200 m/s², about 40.8 kgf. Since centripetal force is a continuous load that grows with the square of speed, reserve a 1.5–2× safety factor when selecting parts (e.g., 400 N × 2 = 800 N) before checking bolts and profiles.

Background: Why I Needed a Centripetal Force Calculator

Recently I was working on a small rotary-stage project and needed to verify the forces on a centrifugal fixture spinning at high speed. The centripetal force formula F=mv2/rF = mv^2/r has only three variables, but when calculating by hand I kept making unit mistakes—plugging rpm directly in as angular velocity, using diameter instead of radius, and forgetting to convert mass to kilograms. After several mismatches against the mechanical handbook data, I decided to use an online calculator to lock down the process and avoid re-deriving the units every time.

Formula and Parameters

The centripetal force required for circular motion has two equivalent forms:

F=mv2r=mω2rF = \frac{mv^2}{r} = m\omega^2 r

And the corresponding centripetal acceleration:

a=v2r=ω2ra = \frac{v^2}{r} = \omega^2 r

These use SI units: mass mm (kg), linear velocity vv (m/s), radius rr (m), and angular velocity ω\omega (rad/s); the resulting force is in newtons (N). If you only have the rotational speed nn (rpm), convert it first with ω=2πn/60\omega = 2\pi n/60; if you have a diameter, divide by 2 to get the radius. These are the two steps where mistakes happen most often.

Running It Through the Online Tool

I used the site's Centripetal Force Calculator. Take a realistic example: a 2 kg counterweight moving along a circle of radius 0.5 m at a linear velocity of 10 m/s.

Hand-check:

F=2×1020.5=400 NF = \frac{2 \times 10^2}{0.5} = 400\ \text{N}

a=1020.5=200 m/s2a = \frac{10^2}{0.5} = 200\ \text{m/s}^2

Entering these three values into the calculator gives 400 N of centripetal force and 200 m/s² of centripetal acceleration, matching the hand calculation. 400 N is about 40.8 kgf, meaning the connection must withstand roughly 40 times the counterweight's own weight in tension—so bolts and structural parts must be verified against this value, not estimated from a static 2 kg load.

Selection Conclusions and Common Mistakes

After several rounds of use, I've summarized the four most common pitfalls:

  1. Rotational speed conversion: rpm must first be converted to rad/s before plugging into the ω2r\omega^2 r form; substituting the raw number can be off by hundreds of times.
  2. Radius vs. diameter: the rr in the formula is the radius; divide a diameter by 2—many people use the outer diameter directly.
  3. Mass units: grams must be converted to kilograms, otherwise the force will be three orders of magnitude too small.
  4. Static-load thinking: centripetal force is a continuous load that grows with the square of speed—doubling the speed quadruples the force—so it cannot be estimated as a static weight.

In practice, I habitually apply a 1.5–2× safety factor to the calculated result before choosing materials. For the 400 N example above, that's 800 N at 2×, and I use that to look up bolt tensile strength and profile specifications.

The same site has several other calculators related to rotary motion and mechanics—such as linear-to-angular velocity conversion and torque/power calculation—that pair well with this Centripetal Force Calculator. Together they let you work through speed, linear velocity, force, and power in one pass, reducing manual conversion steps.

Get new articles by email

Enter your email — we notify you about new articles and releases (unsubscribe anytime).

Related reading

Tech Insights

学习泡妞

学习这件事和泡妞是一回事:为什么不想学、学不会、记不住,蒙卦和逻辑学一句话就点破,一切科学简单到只剩一个「咔嗒」声。用一条条对比的方式,把自学讲成泡妞,看完就忘不掉。

Tech Insights

童话版偏置电路:从电阻分压到 ΔV/R 型,把放大器的「待命点」钉住

放大器的本事全看「待命点」钉在哪:钉得偏,信号一大就削顶;钉得飘,电源一抖就全歪。这篇用斜坡上的木桶讲清偏置是什么,再把六代做法一代代推出来:电阻分压 → 二极管接法当小电阻 → 恒流源当无穷大电阻 → 自偏置四管环(为什么必然「要么死要么不定」)→ 源极垫电阻的 ΔV/R 型 → 大电流的 V/R 型。全篇一套 1.8 V / μCox=200 µA/V² 的数字算到底,附四种结构的电源敏感性对照曲线、五个最容易踩的坑和一屏速记卡。

Tech Insights

童话版电流镜:12 种常用接法一次枚举(附公式、速记卡与选型树)

电流镜只有一句话——共用一个栅压,电流按宽长比被抄过去;但"怎么抄得更稳"有十二条常见路。这篇按"比例 / 叠管子 / 加反馈 / 自己造"四类把常用电流镜全部枚举:单管、源极退化、Widlar、共源共栅、高摆幅、多重共源共栅、威尔逊、改进型威尔逊、增益提升 RGC、β 倍乘、有源电流镜、BJT 版,每种都给 R_out、V_out,min、管数和一句"什么时候用它";再配三代摆幅对照、1.8 V·200 µA·±1% 的选型算例、失配与版图规矩、五个实战场景、七条踩坑和一屏速记卡。