Skip to main content
DD-CAT IDE logoDD-CAT IDE

Article · Tech Insights

Linear and Angular Velocity: v=ωr and RPM Conversion Notes

Favorite

Use v=ωr=2πnr/60 to sort out a rotating body's angular velocity and linear velocity in one step. This article documents my parameter choices, unit conversions, and common mistakes in motor selection, belt pulley, and grinding wheel scenarios, and demonstrates verification with an online calculator.

ShareWeiboXLinkedIn

Key points

The linear-to-angular velocity conversion formula is v=ωr; when speed is given in r/min, v=2πnr/60 with r in meters. For example, at 3000 r/min with a 50 mm (0.05 m) radius, the angular velocity is about 314.16 rad/s and the linear velocity about 15.71 m/s. The radius must be converted from millimeters to meters, or the result will be 1000× too large; also note that radius is not diameter, and angular velocity (rad/s) differs from rotational speed (r/min) by a factor of 2π/60. Applications such as grinding should also check the linear velocity limit in the equipment manual (e.g., grinding wheels are typically 30–80 m/s). An online calculator following v=ω·r=2πn·r/60 can quickly verify these values.

Background: Why Convert Angular Velocity to Linear Velocity

When working on motor selection, belt pulleys, or grinding wheel mechanisms, I often get two numbers: speed n (r/min) and rotating radius r (mm). But when evaluating cutting speed, conveyor belt speed, or centrifugal force, what I actually need is the linear velocity v. Manual calculation isn't hard, but unit conversion and the 2π/60 factor are easy to get wrong. For example, with 3000 r/min and a 50 mm radius, I once did the math in my head and plugged mm directly in as meters, ending up 1000 times too large — my selection nearly went off the rails. The core of the problem comes down to one sentence: angular velocity ω and linear velocity v are related through radius r, and the units must be consistent.

Formula and Parameters

The basic relationship is:

v=ωrv = \omega r

where v is linear velocity (m/s), ω is angular velocity (rad/s), and r is the rotating radius (m). In engineering, speed n (r/min) is more commonly used, and since ω = 2πn/60, it follows that:

v=ωr=2πnr60v = \omega r = \frac{2\pi n r}{60}

When plugging in common parameters, I make a habit of converting the radius from mm to m first. For example, n=3000 r/min, r=50 mm=0.05 m:

ω=2π×300060≈314.16 rad/s\omega = \frac{2\pi \times 3000}{60} \approx 314.16\ \text{rad/s}

v=314.16×0.05≈15.71 m/sv = 314.16 \times 0.05 \approx 15.71\ \text{m/s}

If you forget to divide the radius by 1000, you get 15708 m/s — that order of magnitude is obviously wrong, but it can still throw you off when calculating surface speeds. Angular velocity also has units like °/s, with the conversion ω(rad/s) = ω(°/s) × π/180.

Checking with an Online Calculator

I often use the site's linear velocity and angular velocity calculator, which computes v=ω·r=2πn·r/60. Enter the speed and radius and it outputs both linear velocity and angular velocity, saving me the manual divide-by-60 and factor-of-1000 conversion steps.

I plugged in the earlier example to verify: speed 3000 r/min, radius 50 mm. After entering the two numbers, I got an angular velocity of about 314.16 rad/s and a linear velocity of about 15.71 m/s, matching my manual calculation. For scenarios that require calibrating belt pulley rim speed, grinding wheel grinding speed, or flywheel edge linear velocity, this dual output is much more convenient than computing just one value.

Selection Conclusions and Common Mistakes

When drawing conclusions from the results, I pay attention to several things. Common mistakes:

  1. Using the diameter instead of the radius. r is the radius, not the diameter — with a 100 mm diameter, the radius should be 50 mm, a 2× difference that is simply wrong where precision matters.
  2. Inconsistent units. n uses r/min and r uses mm — if you don't convert r to m before applying the formula, the value comes out 1000 times too large.
  3. Confusing angular velocity with speed. ω is rad/s and n is r/min; they differ by a factor of about 0.10472 (2π/60).
  4. Ignoring the linear velocity limit. For example, grinding wheel speeds are generally recommended at 30–80 m/s; exceeding the safe operating speed is risky, so the calculated v should be checked against the equipment manual.

My experience: first confirm the operating conditions before plugging into the formula, then double-check 2–3 points with the calculator; when there's no network, I keep a small table of common speed/radius combinations as a backup.

For rotating-component selection, I also use:

  • Motor torque and power estimation (P=Tω)
  • Belt pulley transmission ratio calculation
  • Centrifugal force / centripetal acceleration calculation (a=ω²r)
  • Unit conversion tools (mm↔m, rad/s↔°/s)
  • Speed and linear velocity conversion tables

Online tools can reduce manual calculation errors, but safety checks should still keep a safety margin against the equipment manual.

Get new articles by email

Enter your email — we notify you about new articles and releases (unsubscribe anytime).

Related reading

Tech Insights

学习泡妞

学习这件事和泡妞是一回事:为什么不想学、学不会、记不住,蒙卦和逻辑学一句话就点破,一切科学简单到只剩一个「咔嗒」声。用一条条对比的方式,把自学讲成泡妞,看完就忘不掉。

Tech Insights

童话版偏置电路:从电阻分压到 ΔV/R 型,把放大器的「待命点」钉住

放大器的本事全看「待命点」钉在哪:钉得偏,信号一大就削顶;钉得飘,电源一抖就全歪。这篇用斜坡上的木桶讲清偏置是什么,再把六代做法一代代推出来:电阻分压 → 二极管接法当小电阻 → 恒流源当无穷大电阻 → 自偏置四管环(为什么必然「要么死要么不定」)→ 源极垫电阻的 ΔV/R 型 → 大电流的 V/R 型。全篇一套 1.8 V / μCox=200 µA/V² 的数字算到底,附四种结构的电源敏感性对照曲线、五个最容易踩的坑和一屏速记卡。

Tech Insights

童话版电流镜:12 种常用接法一次枚举(附公式、速记卡与选型树)

电流镜只有一句话——共用一个栅压,电流按宽长比被抄过去;但"怎么抄得更稳"有十二条常见路。这篇按"比例 / 叠管子 / 加反馈 / 自己造"四类把常用电流镜全部枚举:单管、源极退化、Widlar、共源共栅、高摆幅、多重共源共栅、威尔逊、改进型威尔逊、增益提升 RGC、β 倍乘、有源电流镜、BJT 版,每种都给 R_out、V_out,min、管数和一句"什么时候用它";再配三代摆幅对照、1.8 V·200 µA·±1% 的选型算例、失配与版图规矩、五个实战场景、七条踩坑和一屏速记卡。